		SIMATIC DP, CPU 1512SP-1 PN for ET 200SP, Central processing unit with Work memory 200 KB for program and 1 MB for data, 1st interface: PROFINET IRT with 3-port switch, 48 ns bit performance, SIMATIC Memory Card required, BusAdapter required for Port 1 and 2
General information
Product type designation		CPU 1512SP-1 PN
HW functional status		FS05
Firmware version		V2.9
Product function
● I&M data		Yes; I&M0 to I&M3
● Module swapping during operation (hot swapping)		Yes; Multi-hot swapping
● Isochronous mode		Yes; Only with PROFINET; with minimum OB 6x cycle of 625 µs
Engineering with
● STEP 7 TIA Portal configurable/integrated from version		V17 (FW V2.9) / V13 SP1 updat 4 (FW V1.8) or higher
Configuration control
via dataset		Yes
Control elements
Mode selector switch		1
Supply voltage
Type of supply voltage		24 V DC
permissible range, lower limit (DC)		19.2 V
permissible range, upper limit (DC)		28.8 V
Reverse polarity protection		Yes
Mains buffering
● Mains/voltage failure stored energy time		5 ms
Input current
Current consumption (rated value)		0.6 A
Current consumption, max.		0.9 A
Inrush current, max.		4.7 A; Rated value
I²t		0.14 A²·s
Power
Infeed power to the backplane bus		8.75 W
Power loss
Power loss, typ.		5.6 W
Memory
Number of slots for SIMATIC memory card		1
SIMATIC memory card required		Yes
Work memory
● integrated (for program)		200 kbyte
● integrated (for data)		1 Mbyte
Load memory
● Plug-in (SIMATIC Memory Card), max.		32 Gbyte
Backup
● maintenance-free		Yes
CPU processing times
for bit operations, typ.		48 ns
for word operations, typ.		58 ns
for fixed point arithmetic, typ.		77 ns
for floating point arithmetic, typ.		307 ns
CPU-blocks
Number of elements (total)		4 000; Blocks (OB, FB, FC, DB) and UDTs
DB
● Number range		1 ... 60 999; subdivided into: number range that can be used by the user: 1 ... 59 999, and number range of DBs created via SFC 86: 60 000 ... 60 999
● Size, max.		1 Mbyte; For DBs with absolute addressing, the max. size is 64 KB
FB
● Number range		0 ... 65 535
● Size, max.		200 kbyte
FC
● Number range		0 ... 65 535
● Size, max.		200 kbyte
OB
● Size, max.		200 kbyte
● Number of free cycle OBs		100
● Number of time alarm OBs		20
● Number of delay alarm OBs		20
● Number of cyclic interrupt OBs		20; With minimum OB 3x cycle of 500 µs
● Number of process alarm OBs		50
● Number of DPV1 alarm OBs		3
● Number of isochronous mode OBs		1
● Number of technology synchronous alarm OBs		2
● Number of startup OBs		100
● Number of asynchronous error OBs		4
● Number of synchronous error OBs		2
● Number of diagnostic alarm OBs		1
Nesting depth
● per priority class		24
Counters, timers and their retentivity
S7 counter
● Number		2 048
Retentivity
— adjustable		Yes
IEC counter
● Number		Any (only limited by the main memory)
Retentivity
— adjustable		Yes
S7 times
● Number		2 048
Retentivity
— adjustable		Yes
IEC timer
● Number		Any (only limited by the main memory)
Retentivity
— adjustable		Yes
Data areas and their retentivity
Retentive data area (incl. timers, counters, flags), max.		128 kbyte; Available retentive memory for bit memories, timers, counters, DBs, and technology data (axes): 88 KB
Flag
● Size, max.		16 kbyte
● Number of clock memories		8; 8 clock memory bit, grouped into one clock memory byte
Data blocks
● Retentivity adjustable		Yes
● Retentivity preset		No
Local data
● per priority class, max.		64 kbyte; max. 16 KB per block
Address area
Number of IO modules		2 048; max. number of modules / submodules
I/O address area
● Inputs		32 kbyte; All inputs are in the process image
● Outputs		32 kbyte; All outputs are in the process image
per integrated IO subsystem
— Inputs (volume)		8 kbyte
— Outputs (volume)		8 kbyte
per CM/CP
— Inputs (volume)		8 kbyte
— Outputs (volume)		8 kbyte
Subprocess images
● Number of subprocess images, max.		32
Address space per module
● Address space per module, max.		288 byte; For input and output data respectively
Address space per station
● Address space per station, max.		2 560 byte; for central inputs and outputs; depending on configuration; 2 048 bytes for ET 200SP modules + 512 bytes for ET 200AL modules
Hardware configuration
Number of distributed IO systems		32; A distributed I/O system is characterized not only by the integration of distributed I/O via PROFINET or PROFIBUS communication modules, but also by the connection of I/O via AS-i master modules or links (e.g. IE/PB-Link)
Number of DP masters
● Via CM		1
Number of IO Controllers
● integrated		1
● Via CM		0
Rack
● Modules per rack, max.		80; CPU + 64 modules + server module (mounting width max. 1 m) + 16 ET 200AL modules
● Quantity of operable ET 200SP modules, max.		64
● Quantity of operable ET 200AL modules, max.		16
● Number of lines, max.		1
PtP CM
● Number of PtP CMs		the number of connectable PtP CMs is only limited by the number of available slots
Time of day
Clock
● Type		Hardware clock
● Backup time		6 wk; At 40 °C ambient temperature, typically
● Deviation per day, max.		10 s; Typ.: 2 s
Operating hours counter
● Number		16
Clock synchronization
● supported		Yes
● to DP, master		Yes; Via CM DP module
● to DP, slave		Yes; Via CM DP module
● in AS, master		Yes
● in AS, slave		Yes
● on Ethernet via NTP		Yes
Interfaces
Number of PROFINET interfaces		1
Number of PROFIBUS interfaces		1; Via CM DP module
Optical interface		Yes; via BusAdapter
1. Interface
Interface types
● RJ 45 (Ethernet)		Yes; X1 P3; opt. X1 P1 and X1 P2 via BusAdapter BA 2x RJ45
● Number of ports		3; 1. integr. + 2. via BusAdapter
● integrated switch		Yes
● BusAdapter (PROFINET)		Yes; compatible BusAdapters: BA 2x RJ45, BA 2x M12, BA 2x FC, BA 2x LC, BA LC/RJ45, BA LC/FC, BA 2x SCRJ, BA SCRJ/RJ45, BA SCRJ/FC,
Protocols
● IP protocol		Yes; IPv4
● PROFINET IO Controller		Yes
● PROFINET IO Device		Yes
● SIMATIC communication		Yes
● Open IE communication		Yes; Optionally also encrypted
● Web server		Yes
● Media redundancy		Yes; MRP Automanager according to IEC 62439-2 Edition 2.0
PROFINET IO Controller
Services
— PG/OP communication		Yes
— Isochronous mode		Yes
— Direct data exchange		Yes; Requirement: IRT and isochronous mode (MRPD optional)
— IRT		Yes
— PROFIenergy		Yes; per user program
— Prioritized startup		Yes; Max. 32 PROFINET devices
— Number of connectable IO Devices, max.		128; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET
— Of which IO devices with IRT, max.		64
— Number of connectable IO Devices for RT, max.		128
— of which in line, max.		128
— Number of IO Devices that can be simultaneously activated/deactivated, max.		8; in total across all interfaces
— Number of IO Devices per tool, max.		8
— Updating times		The minimum value of the updat time also depends on communication share set for PROFINET IO, on the number of IO devices, and on the quantity of configured user data
updat time for IRT
— for send cycle of 250 µs		250 μs to 4 ms; Note: In the case of IRT with isochronous mode, the minimum updat time of 500 µs of the isochronous OB is decisive
— for send cycle of 500 µs		500 µs to 8 ms
— for send cycle of 1 ms		1 ms to 16 ms
— for send cycle of 2 ms		2 ms to 32 ms
— for send cycle of 4 ms		4 ms to 64 ms
— With IRT and parameterization of "odd" send cycles		updat time = set "odd" send clock (any multiple of 125 µs: 375 µs, 625 µs ... 3 875 µs)
updat time for RT
— for send cycle of 250 µs		250 µs to 128 ms
— for send cycle of 500 µs		500 µs to 256 ms
— for send cycle of 1 ms		1 ms to 512 ms
— for send cycle of 2 ms		2 ms to 512 ms
— for send cycle of 4 ms		4 ms to 512 ms
PROFINET IO Device
Services
— PG/OP communication		Yes
— Isochronous mode		No
— IRT		Yes
— PROFIenergy		Yes; per user program
— Shared device		Yes
— Number of IO Controllers with shared device, max.		4
— activation/deactivation of I-devices		Yes; per user program
— Asset management record		Yes; per user program
2. Interface
Interface types
● RS 485		Yes; Via CM DP module
● Number of ports		1
Protocols
● PROFIBUS DP master		Yes
● PROFIBUS DP slave		Yes
● SIMATIC communication		Yes
PROFIBUS DP master
● Number of connections, max.		48; Of which 4 each reserved for ES and HMI
● Number of DP slaves, max.		125; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET
Services
— PG/OP communication		Yes
— Equidistance		No
— Isochronous mode		No
— Activation/deactivation of DP slaves		Yes
Interface types
RJ 45 (Ethernet)
● 100 Mbps		Yes
● Autonegotiation		Yes
● Autocrossing		Yes
● Industrial Ethernet status LED		Yes
RS 485
● Transmission rate, max.		12 Mbit/s
Protocols
Number of connections
● Number of connections, max.		128; via integrated interfaces of the CPU and connected CPs / CMs
● Number of connections reserved for ES/HMI/web		10
● Number of connections via integrated interfaces		88
● Number of connections per CP/CM		32
● Number of S7 routing paths		16
Redundancy mode
● H-Sync forwarding		Yes
Media redundancy
— Media redundancy		Yes; only via BusAdapter
— MRP		Yes; MRP Automanager according to IEC 62439-2 Edition 2.0, MRP Manager; MRP Client
— MRP interconnection, supported		Yes; as MRP ring node according to IEC 62439-2 Edition 3.0
— MRPD		Yes; Requirement: IRT
— Switchover time on line break, typ.		200 ms; For MRP, bumpless for MRPD
— Number of stations in the ring, max.		50
SIMATIC communication
● PG/OP communication		Yes; encryption with TLS V1.3 pre-selected
● S7 routing		Yes
● Data record routing		Yes
● S7 communication, as server		Yes
● S7 communication, as client		Yes
● User data per job, max.		See online help (S7 communication, user data size)
Open IE communication
● TCP/IP		Yes
— Data length, max.		64 kbyte
— several passive connections per port, supported		Yes
● ISO-on-TCP (RFC1006)		Yes
— Data length, max.		64 kbyte
● UDP		Yes
— Data length, max.		2 kbyte; 1 472 bytes for UDP broadcast
— UDP multicast		Yes; Max. 5 multicast circuits
● DHCP		Yes
● DNS		Yes
● SNMP		Yes
● DCP		Yes
● LLDP		Yes
● Encryption		Yes; Optional
Web server
● HTTP		Yes; Standard and user pages
● HTTPS		Yes; Standard and user pages
OPC UA
● Runtime license required		Yes; "Small" license required
● OPC UA Client		Yes
— Application authentication		Yes
— Security policies		Available security policies: None, Basic128Rsa15, Basic256Rsa15, Basic256Sha256
— User authentication		"anonymous" or by user name & password
— Number of connections, max.		4
— Number of nodes of the client interfaces, max.		1 000
— Number of elements for one call of OPC_UA_NodeGetHandleList/OPC_UA_ReadList/OPC_UA_WriteList, max.		300
— Number of elements for one call of OPC_UA_NameSpaceGetIndexList, max.		20
— Number of elements for one call of OPC_UA_MethodGetHandleList, max.		100
— Number of simultaneous calls of the client instructions per connection (except OPC_UA_ReadList,OPC_UA_WriteList,OPC_UA_MethodCall), max.		1
— Number of simultaneous calls of the client instructions OPC_UA_ReadList,OPC_UA_WriteList and OPC_UA_MethodCall, max.		5
— Number of registerable nodes, max.		5 000
— Number of registerable method calls of OPC_UA_MethodCall, max.		100
— Number of inputs/outputs when calling OPC_UA_MethodCall, max.		20
● OPC UA Server		Yes; Data access (read, write, subscribe), method call, custom address space
— Application authentication		Yes
— Security policies		Available security policies: None, Basic128Rsa15, Basic256Rsa15, Basic256Sha256
— User authentication		"anonymous" or by user name & password
— GDS support (certificate management)		Yes
— Number of sessions, max.		32
— Number of accessible variables, max.		50 000
— Number of registerable nodes, max.		10 000
— Number of subscriptions per session, max.		20
— Sampling interval, min.		100 ms
— Publishing interval, min.		500 ms
— Number of server methods, max.		20
— Number of inputs/outputs per server method, max.		20
— Number of monitored items, max.		1 000; for 1 s sampling interval and 1 s send interval
— Number of server interfaces, max.		10 of each "Server interfaces" / "Companion specification" type and 20 of the type "Reference namespace"
— Number of nodes for user-defined server interfaces, max.		1 000
● Alarms and Conditions		Yes
— Number of program alarms		100
— Number of alarms for system diagnostics		50
Further protocols
● MODBUS		Yes; MODBUS TCP
S7 message functions
Number of login stations for message functions, max.		32
Program alarms		Yes
Number of configurable program messages, max.		5 000; Program messages are generated by the "Program_Alarm" block, ProDiag or GRAPH
Number of loadable program messages in RUN, max.		2 500
Test commissioning functions
Joint commission (Team Engineering)		Yes; Parallel online access possible for up to 5 engineering systems
Status block		Yes; Up to 8 simultaneously (in total across all ES clients)
Single step		No
Number of breakpoints		8
Status/control
● Status/control variable		Yes
● Variables		Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters
● Number of variables, max.
— of which status variables, max.		200; per job
— of which control variables, max.		200; per job
Forcing
● Forcing		Yes
● Forcing, variables		Peripheral inputs/outputs
● Number of variables, max.		200
Diagnostic buffer
● present		Yes
● Number of entries, max.		1 000
— of which powerfail-proof		500
Traces
● Number of configurable Traces		4; Up to 512 KB of data per trace are possible
Interrupts/diagnostics/status information
Diagnostics indication LED
● RUN/STOP LED		Yes
● ERROR LED		Yes
● MAINT LED		Yes
● Monitoring of the supply voltage (PWR-LED)		Yes
● Connection display LINK TX/RX		Yes
Supported technology objects
Motion Control		Yes; Note: The number of technology objects affects the cycle time of the PLC program; selection guide via the TIA Selection Tool
● Number of available Motion Control resources for technology objects		800
● Required Motion Control resources
— per speed-controlled axis		40
— per positioning axis		80
— per synchronous axis		160
— per external encoder		80
— per output cam		20
— per cam track		160
— per probe		40
● Positioning axis
— Number of positioning axes at motion control cycle of 4 ms (typical value)		5
— Number of positioning axes at motion control cycle of 8 ms (typical value)		10
Controller
● PID_Compact		Yes; Universal PID controller with integrated optimization
● PID_3Step		Yes; PID controller with integrated optimization for valves
● PID-Temp		Yes; PID controller with integrated optimization for temperature
Counting and measuring
● High-speed counter		Yes
Standards, approvals, certificates
Highest safety class achievable in safety mode
● Performance level according to ISO 13849-1		none
● SIL acc. to IEC 61508		No
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.		-25 °C; No condensation
● horizontal installation, max.		60 °C
● vertical installation, min.		-25 °C; No condensation
● vertical installation, max.		50 °C
Altitude during operation relating to sea level
● Installation altitude above sea level, max.		5 000 m; Restrictions for installation altitudes > 2 000 m, see manual
Configuration
Programming
Programming language
— LAD		Yes
— FBD		Yes
— STL		Yes
— SCL		Yes
— GRAPH		Yes
Know-how protection
● User program protection/password protection		Yes
● Copy protection		Yes
● Block protection		Yes
Access protection
● protection of confidential configuration data		Yes
● Protection level: Write protection		Yes
● Protection level: Read/write protection		Yes
● Protection level: Complete protection		Yes
Cycle time monitoring
● lower limit		adjustable minimum cycle time
● upper limit		adjustable maximum cycle time
Dimensions
Width		100 mm
Height		117 mm
Depth		75 mm
Weights
Weight, approx.		310 g